The tin bath is the defining section of a float glass line. Molten glass floats on a bath of liquid tin, and its thickness and surface quality are governed by a carefully controlled temperature profile maintained by hundreds of heating elements arranged in zones across the bath roof. Those zones are supplied by dry-type cast resin units installed close to the line, in an environment that is warm, electrically noisy and intolerant of unplanned interruption. Commissioning this equipment properly is the difference between a stable ribbon and weeks of thickness variation that nobody can trace to a single cause.
Cast resin units are chosen for tin bath heating because they eliminate oil from a location where a leak would contaminate the process and create a serious fire hazard. The windings are encapsulated in epoxy under vacuum, giving good resistance to dust and moisture and allowing installation inside the building close to the load. That proximity reduces the length of high-current secondary cabling, which matters when the heating circuits carry large currents at low voltage.
The trade-offs are equally real. Cast resin has a lower thermal mass than an oil filled system, so it responds faster to load changes and to cooling failures. Its insulation coordination is governed by IEC 60076-11 rather than the oil immersed parts of the standard family, and partial discharge performance is a central quality indicator. The enclosure protection class, the ventilation path and the clearance to surrounding steelwork all influence the attainable continuous rating. A unit that performs perfectly on a factory test bench can run hot in a cramped tin bath gallery.
Pre-Energization Checks
Commissioning begins before any cable is terminated. The shipping records, the nameplate and the approved datasheet should be compared for rating, voltage ratio, vector group, impedance, insulation level and temperature class. Physical inspection covers the epoxy surface for cracks or delamination, the core and clamp earthing, the tightness of busbar joints, the condition of surge arresters, and the free movement of any ventilation dampers. Dust and construction debris inside the enclosure must be removed with dry compressed air or a vacuum, never with a solvent that could attack the resin surface.
Electrical tests follow a logical order. Insulation resistance is measured with the appropriate direct voltage, with the results recorded together with the ambient temperature and humidity so that later readings remain comparable. Winding resistance is measured on every tap position and corrected to the reference temperature; a deviation between phases above one percent warrants investigation before proceeding. Voltage ratio and vector group are confirmed on each tap, and the continuity of the earthing conductor is verified with a low-resistance test rather than a visual check alone.
Dielectric and Partial Discharge Evidence
The factory routine tests should include an applied-voltage test and an induced overvoltage test, plus a partial discharge measurement at the specified voltage sequence. The site team should obtain and review those reports rather than assuming they exist. Where the project specifies it, a repeat partial discharge measurement on site provides a valuable baseline: cast resin insulation can be damaged by rough handling, and a reading that has risen between factory and site is a clear warning sign.
Partial discharge magnitude is normally expressed in picocoulombs and interpreted against the limits in IEC 60076-11. Because the measurement is sensitive to external interference, the test should be scheduled when the tin bath heaters, nearby variable-speed drives and welding work are quiet. Recording the background noise level alongside the result makes the report far more useful when it is revisited years later.
Temperature Control and Interlocks
Almost every cast resin unit for this duty is fitted with embedded temperature sensors, a controller and forced-air cooling. Commissioning must verify the entire alarm and trip chain, not merely that the display shows a plausible number. The sensors should be checked against a traceable reference, the fan rotation and airflow direction confirmed, and each alarm threshold simulated to prove that the correct annunciation appears in the line control system. The trip contact should be tested up to the breaker or contactor that actually removes the supply.
It is worth documenting the relationship between load current, winding temperature and ambient at this stage. A unit that reaches its alarm threshold at 70 percent of rated current during a summer campaign is telling the team something about ventilation that no factory test will reveal. That baseline also informs the derating policy if a fan is later taken out of service for maintenance.
First Energization and Load Ramp
The initial energization is normally done at no load, with the downstream heating circuits open, and ideally with the supply capable of being interrupted immediately. Inrush current on a dry-type unit can be substantial, so the upstream protection settings should be reviewed against the manufacturer's inrush data. A no-load soak of several hours allows the team to check for abnormal noise, vibration, odour or localized heating with an infrared camera.
Load is then introduced zone by zone. Each tin bath zone should be brought up in a planned sequence while secondary current, phase voltage, power factor and winding temperature are logged. Three-phase balance deserves particular attention because uneven heating across the bath width translates directly into ribbon thickness variation. Harmonics introduced by the power controllers should be measured with a power quality analyser and compared with the design assumption; if the total harmonic distortion of current exceeds the specified duty, the resulting extra eddy heating must be accounted for in the continuous rating.
Integration With the Process Control System
The electrical commissioning is not complete until the tin bath supervisory system can see and interpret the supply state. Tap position, winding temperature, fan status, alarm and trip signals, and per-zone current should all be mapped and labelled consistently. Trending these alongside ribbon thickness and bath temperature gives the process engineers a diagnostic tool that is otherwise unavailable. When a thickness deviation appears, the first question is often whether a heating zone lost output; a well-integrated record answers that in seconds.
Documentation should also include the as-built single-line diagram, the protection settings with their calculation basis, the test certificates, the spare-parts list and the manufacturer's maintenance intervals. A transformer supplied for a float line is usually one of several near-identical units, and keeping a distinct serial-numbered file for each one prevents the common mistake of applying a generic maintenance schedule to a zone that runs consistently hotter than its neighbours.
Handover Criteria
A practical handover checklist is short but demanding: all routine test reports received and reviewed; site measurements within tolerance and recorded with ambient conditions; the full alarm and trip chain proven end to end; a documented load ramp with stable three-phase currents and acceptable temperatures at full zone output; power quality within the specified harmonic envelope; and operator training completed on the temperature controller and the emergency isolation procedure. Meeting those criteria before the first production ribbon is drawn costs a few days. Discovering a missing interlock or a blocked ventilation path afterwards can cost a great deal more, because a tin bath cannot simply be switched off and restarted without significant process consequences.